产品展示
当前位置:
首页
/
/
S301 纯铝焊丝
浏览量:
1000

S301 纯铝焊丝

铝及铝合金焊丝广泛用于铝及其合金氩弧焊及氧-乙炔气焊时作填充材料。氩弧焊是焊接铝及铝合金较完善的方法。氩弧焊可以不用熔剂,但氧-乙炔气焊时必须配铝气焊熔剂共同使用。焊丝的选择,主要根据母材的种类,对接头的抗裂性能,机械性能及抗腐蚀性能等方面的要求综合考虑。
所属分类 :
无分类内容
零售价
0.0
市场价
0.0
浏览量:
1000
产品编号
数量
-
+
库存:
产品描述
参数

标准:

符合GB SAI1070

相当AWS ER1100

说明:

S301是含铝大于99.5%的纯铝焊丝。具有良好的可焊性和耐蚀性,以及优良的塑性及韧性,但强度较低。

S301 is pure aluminum welding wire with aluminum content greater than 99.5%. It has good weldability and corrosion resistance, as well as excellent plasticity and toughness, but low strength.

用途:

氩弧焊及氧-乙炔气焊焊接纯铝及对接头性能要求不高的铝合金作填充材料,广泛应用于化学工业铝制设备上。

Argon arc welding and oxygen-acetylene gas welding are used as filler materials for pure aluminum and aluminum alloys that do not require high joint performance. They are widely used in aluminum equipment in the chemical industry.

焊丝化学成分:

Si Fe Cu Mn Al
≤0.3 ≤0.3 ≤0.04 ≤0.03 余量

供应规格(mm):

盘装Φ 1.0 1.2 1.5 2.0 2.5    
焊丝直径Φ
(长度1000)
1.5 2.0 2.5 3.0 4.0 5.0 6.0

注意事项:

1. 焊前应严格清除工件焊接边缘和焊丝表面的氧化膜和油污等污物,否则会使焊缝产生熔合不良并引起气孔、夹渣等缺陷。

2. 为了保证焊透而又不导致塌陷,施焊时可采用垫板以托住熔化金属。

3. 氧-乙炔气焊时必须配铝气焊熔剂共同使用。

1. Strictly remove the oxide film and oil stains on the welding edge of the workpiece and the surface of the welding wire before welding, otherwise it will cause poor fusion of the weld and cause defects such as pores and slag inclusion.

2. In order to ensure penetration without causing collapse, a backing plate can be used to hold the molten metal during welding.

3. Oxygen-acetylene gas welding must be used together with aluminum gas welding flux.

扫二维码用手机看
未找到相应参数组,请于后台属性模板中添加
上一个
下一个
暂时没有内容信息显示
请先在网站后台添加数据记录。
获取产品详细信息
我们的工作人员将会在24小时之内(工作日)联系您,如果需要其他服务,欢迎拨打服务热线: 0774-8518000
全部评论
已有0条评论
暂时没有内容信息显示
请先在网站后台添加数据记录。
搜索
确认
取消
岑溪天马石业

服务热线

联系我们

地址:广西岑溪市义洲大道49号-51号

工厂地址:梧州市岑溪市糯垌镇新塘三兴村三兴工业园区

电话:139-6030-2512

中文网址:天马石业.网址

在线留言

留言应用名称:
客户留言
描述:
验证码

岑溪天马石业

Copyright © 2021   广西岑溪天马石业股份有限公司  All right reserved.  桂ICP备2023005680号-1   网站建设:中企动力 南宁